Hook up amp to factory radio, report abuse

Hook up amp to factory radio
Hook up amp to factory radio

This converter can then be connected directly to your amplifier's line level inputs. If you don't hear distortion even at the loudest setting, online male the head unit is in good shape. Their toll-free number would on your invoice. They can cause noticeable power loss when higher wattages try to get through. Position your amp and speaker in your car.

Hide all of the cables and wires behind carpeting, panels or trim for a cleaner and more professional look. The speaker wire solution we've shared here is a simpler, less-expensive alternative that will work for most people. Most amplifiers have rca inputs.

Video of the Day

For information about other aspects of amplifier installation, like power and ground wiring, check out our Amplifier Installation Guide. Connect the ground from the amplifier to the chassis. Using rca splitters would decrease the voltage going to the amp. Mount your amplifier on a solid surface that will not conduct electricity. Turn up the deck's volume until you hear distortion, and set it just below that level.

Buck Pomerantz

This will prevent noise in the system. Use the front speaker wires, front left and front right, for your amp's inputs and outputs. Then I discovered all the H.

How to Wire an Amp & Subwoofers Into a Stock Stereo

David, I'm not sure what you're intending, but the eight conductors should never be connected together. Connect the red power wire and ground wire you prepped earlier to the proper inputs on your amp. If you have a factory deck and install an amp, there's really no wire to connect the amp to on the factory deck. Consult the owner's manual or the manufacturer of your amplifier to determine the size fuse you should use.

So if you're upgrading a complex system, using a line output converter might be your best option. Run two of these cables from the dash to your new amplifier. To really highlight the bass of your car stereo, you need a setup capable of properly reproducing low frequency notes. Is this article up to date? Our customers were recording studios, nightclubs, and touring bands.

If they are, then hook up an external speaker to the radio's output for that side to see if it is the radio at fault. My amp has speaker level inputs and I was wondering if I need to hook that up to two speakers to work or can I just run it off one. Run this wire back to your amp and hook it into the speaker-level inputs. Another popular way to connect an amplifier to a factory radio is to use something called a line output converter.

Secure all of the amp's connections tightly using a screwdriver. Why buy from an authorized dealer? Many other amps feature similar connections. Component speakers installation options.

Hook up amp to factory radio

Hook Up AMP To Factory Radio

Most amplifiers will have outputs for at least two speakers. No wiring harness available yet. Already answered Not a question Bad question Other. Make sure to put the right rear positive wire into the right rear positive speaker-level input, and do the same for right rear negative wire until all four of the wires are connected. Carefully splice into the positive and negative wire on both the right and left rear speakers using a wire stripper.

Hook up amp to factory radio

Why don't you give us a call so an Advisor can help you get all the gear you need for a successful install. In your case, with only a single speaker wire to tap into, you either tap the speaker wires twice, for the positive and negative left and right inputs, or just use one input. Situate these wires away from the power wires. Your reply will be sent to Continue where you left off. Generally, dating at 47 the positive wire will be red and the negative will be black.

How to Install a Car Amp (with Pictures) - wikiHow

If the amp doesn't seem to be working properly, disconnect your battery again and go back and double-check all of your wiring for possible damaged wire, grounded wire or loose connections. If the sound is scratchy, check that your connections are secure. Manoj, site I don't know what kinds of wiring and connectors are available in your country.

That way, once the cables are in place, you'll know which of those cables is for the amp inputs and which is for the amp outputs. Once you've identified each of the eight speaker wires, cut each one. It is best to install it as close as possible to the connection.

Christopher, The second diagram of this article might help visualize what you want to do. Include your email address to get a message when this question is answered. This article was written by the It Still Works team, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. The radio's wiring harness delivers power to the radio and sends its output to the speakers.

It has only four speakers. Disconnect the negative battery terminal. Subwoofers can be large speakers that are usually housed in speaker enclosures installed in the trunk of the car. Our day money-back guarantee. Now that your amp is tapped into your car's factory audio system, run speaker wires from the amp's speaker outputs to the speaker s or sub-woofer s you want the amp to power.

Hook Up AMP To Factory Radio

Report Abuse

  1. Also since I am using speaker level inputs, the line output converter is not needed, it is already in the amp.
  2. Track your shipment How to return a product.
  3. Adding a subwoofer and amplifier to your existing stereo is a great way to improve the bottom-end output of your system and is one of the most common upgrades performed on a car's audio gear.
  4. Paint the hole's edges to protect against rust.
  5. Make sure your speaker's impedance in ohms matches the output impedance of your amplifier.

Take that fuse out, wrap the remote wire around it, and connect it back where it was. Is there no other way to do get this to work without replacing the head unit? If there is no available hole, use a power drill and steel bits to drill one.

How to Add an Amplifier to a Factory Stereo

Check the manuals included with your line-out converter, stereo and amplifier for complete installation instructions for your system. Sometimes, the music cuts out when I turn on the car. When do you want us to call you back?

It Still Works

Then send the amp's outputs back to the stereo's harness, and on to the speakers through the factory wiring. He says it's due to the factory radio but I am not buying this. If you look closely, some of the photos show the speaker-level input harness connections, where you use an included harness attached to speaker wires coming from the radio's output. Rate your experience with us. Click on this link for details.

  • Insert the main power wire fuse once all the connections for the other wires are in place.
  • Make sure the car is completely turned off to avoid electrical shock or injury.
  • Share your experience with Bill Crutchfield.
  • You can usually find one on the sidewall behind the carpeting.

It sounds like you should call Crutchfield and talk to an Advisor who'll have all the information necessary to help you get great sound in your car with some aftermarket speakers. You can make all the speaker connections without having to solder or crimp anything. Can't find your exact vehicle? Eventually I moved back to Charlottesville, dating Virginia and opened a small demo recording studio.

Yahoo Answers

Set equalizers to their center, or neutral, position if you have them. You'll need to identify which wire goes to which speaker. You are in line to receive a call from. Otherwise, this wiring technique described in this article doesn't apply to systems with a factory amplifier.

  • The meaning of a dating relationship
  • Speed dating youth group
  • Dating country sites
  • Wtf pictures from russian dating websites
  • Rsd dating profile
  • Same sex dating apps
  • Online dating male description examples
  • Site de dating online